Dear All,
I have a Nichiyu FB20P forklifts. When start machine, a few of minutes, the error message "A14 sensor-current (amateture)" and " A15 sensor-current(Field)" occur. I have no experience about Forklift. Please give me advise and electric diagram.
Thanks!
Showing items 21 - 33 of 33 results.
can u helpe me about travel contact problem in nichiyu forklift
Hello Marc,
Merry Christmas to you and your family!
The sensor that was handing out seems to belong to the hydraulic brake reservoir and is defective!
I did check the oil level and it is OK, so will hunt for a sensor (magnetic reed switch?) in the local market. Else will change the reservoir and sensor in one go using local automobile parts.
I will send the picture a little later.
I'm glad that the problem is solved, luckily not an expensive repair.
About the picture you can send them to marc ad tuvo dot be, I'll try to assist you in solving them as well.
regards (happy Christmas for you and your family)
Marc b
Hello Marc,
The problem was as your suggested. One wire of the hand brake switch was disconnected. Reconnecting this solved teh problem.
Thank you very much!
I also discovered on sensor that was just hanging loose below the floor board near the steering column. I have taken a picture of this but am not sure how to send this to you.
Another question I have is regarding the steering sensor. What type of sensor is this? Is it a tacho generator? It is fixed on the shaft leading to the steering motor after the steering column. I was expecting this to be attached to the steering column.
The rear parking lights and brake lights are not functioning on this machine. The brake light switch seems to be missing from the brake pedal area and I see 2 wires there. The bulbs on the reas lamps are OK.
Hello tkjith, So if I unstand it correctly the EPS contactor doesn't close. If so measure on the 6 pole connector of the EPS controller pin 3 (red or orange wire). Key switch on and parking brake off, must be battery voltage if not control the parking brake switch and wiring of it. Let me know what you measure.
Kind regards and merry Christmas
marc b
hello, I have an FB20p-50c-430m serial no 210236 that has a power steering unit failure. No error code displayed. Am not sure how the steering information is sensed and conveyed to the EPS controller. Controller is not getting power via the contactor and am assuming that the contactor will come on only is eps sensors are ok. Hydraulic and front rear movements are ok.Any tips will be helpful. Are user manuals and technical service/ repair socuments available?
HI marc
Can you help me with the service manuals for Nichiyu models:
FB15P - 75 - 300 SF
FB15PN - 75B - 350 DRP
FB15PN - 75 - 350
FB15PN - 70 - 350
FB14PN - 70 - 300 SF
FB15P - 70 - 300 AF
Hello Pankaj,
help has been send.
marc b
Hi Marcb,
This is pankaj, I have Nichiyu Forklift (Details Below)
The model : FB20PN-60B-400MCS
S/N: 241AA1317
Can you help me with the wiring diagam of the same?
my mail ID is marketing at asiangrpindia dot com.
Looking forward for your support.
regards,
Pankaj
Hi Marcb,
Please contact me by email [email address removed].
I am looking forward your email.
Best reagrds!
Jack
Hey Jack, please putyour email in your profile. I will send the needed information. Oh 3200$ for an printcard that's indeed very expensive!! next time if you need parts just send me an email.
kind regards
Marcb
Hi Marc-b!
Thanks for your reply!
The model : FB20PN-D070C-470M
S/N: 227D02367.
I changed the other control board, it is OK. But I want to understand clearly about root cause for future. Because price of control board is so expensive about 3200$.
Best regards
Jack
Hey Jack, if you want to have some assistance with the problem you're having you have to complete the model and serial number.
Examble; FB20PN-70BC sn;288AD0098
Kind regards
marcb
Forkliftaction accepts no responsibility for forum content and requires forum participants to adhere to our rules of conduct. Click here for more information.
If you are having trouble using the Discussion Forums, please contact us for help.