Search Forums

-
Showing items 1 - 20 of 111,720 results.
Maintenance & Troubleshooting
Mechanic
Posted: 4 Jul 2025 23:31 by Scott_
First check your limit and steering switches make sure both drive motors are turning when going straight next l would...
Maintenance & Troubleshooting
grove T80
Posted: 4 Jul 2025 16:55 by michel_v
174 / 5.000
does anyone have a book of this print is in a grove T80
very often lamp 4...
Maintenance & Troubleshooting
Mechanic
Posted: 4 Jul 2025 06:50 by DyslexicNerd_01
Are you saying you can't travel at all or you can't increase the speed limiter?
Using an SCR controller you...
News & Perspectives
UK IMHX Exhibition
Posted: 4 Jul 2025 06:37 by Data
Just seen the IMHX exhibition is back this September and wondered what the UK's thoughts on whether it's worth going?...
Maintenance & Troubleshooting
Mechanic
Posted: 4 Jul 2025 06:24 by jimmy_s
Crown RC3000, EV100, speed does not increase in scr mode, potentiometer readings are correct.
Maintenance & Troubleshooting
Forklift, Battery & Charger (please i need help in this)
Posted: 4 Jul 2025 04:04 by Oscar_Valdez
I have a similar but different problem. My battery was overhauled, regenerated, and the modules on my forklift replaced, but...
Maintenance & Troubleshooting
RC5500
Posted: 4 Jul 2025 00:03 by John_Nix
Check the connectors on the top and bottom of your distribution board.
Maintenance & Troubleshooting
RC5500
Posted: 3 Jul 2025 23:19 by RamKhudan
good morning, dear,

Crown RC5500
Shuts off few seconds when turned on
I swap from a working forklift all the...
Maintenance & Troubleshooting
Will not Accelerate just Idles
Posted: 3 Jul 2025 23:01 by Rat1
Hi Guys Just letting you know that we did check out the Hyd control Valve and notice that my guy...
Maintenance & Troubleshooting
Counterweight sits too low for bolt - Hyster H60XM
Posted: 3 Jul 2025 13:14 by lumberjack
Anyone ever seen a counterweight sit ok on the hooks but the rear bolt hole is too low for the...
Maintenance & Troubleshooting
Event Code 305
Posted: 3 Jul 2025 02:10 by Jared_Riley
In my experience after troubleshooting this code, it will be a bad access 3. If following the book it will...
Maintenance & Troubleshooting
Code 305
Posted: 3 Jul 2025 02:07 by Jared_Riley
More than likely in my experience it will be a failure in access 3. If you have another RC with...
Maintenance & Troubleshooting
8FD40U display
Posted: 3 Jul 2025 00:21 by Chris_Henry
So I have no power to my display. Unit has the combo meter. I checked all fuses and relays in...
Maintenance & Troubleshooting
David
Posted: 2 Jul 2025 16:40 by Davewrtyyhhvccv
Hi there
Wonder if anybody could help
Jung heinrich tfg425. lpg wont start when engine hot,
It has the Nissan...
Maintenance & Troubleshooting
NO SPARK
Posted: 2 Jul 2025 03:45 by Hemi
I have a YALE FORKLIFT model GLC050VXNVRE083.i have the MAZDA 2.2L engine. It was working fine and the next day...
Maintenance & Troubleshooting
Will not Accelerate just Idles
Posted: 2 Jul 2025 03:10 by Rat1
Hi and Thanks for all the Suggestions But this Lift has a Throttle cable all the way back to the...
Maintenance & Troubleshooting
Will not Accelerate just Idles
Posted: 2 Jul 2025 02:34 by John_Bradley
Look at your accelerator pot for damaged wiring as well. should be 5 volts going to pot and the...
Maintenance & Troubleshooting
Will not Accelerate just Idles
Posted: 2 Jul 2025 02:18 by Scott_
I read all the post you said you changed out the hyd control valve and then this started are you...
Safety & Training
(Demerit) Point System for Lifts
Posted: 1 Jul 2025 22:54 by Oatman
This is a really old post, but does anyone have any current info about a demerit point system they could...
Maintenance & Troubleshooting
Will not Accelerate just Idles
Posted: 1 Jul 2025 15:05 by Dil_Era
Do you have IFAK Cable with PCST to Diagnosis

Forkliftaction accepts no responsibility for forum content and requires forum participants to adhere to our rules of conduct. Click here for more information.

If you are having trouble using the Discussion Forums, please contact us for help.

Nichiyu FB28PN77B367RRC
Yokohama, Japan
Used - Sale
Crown RD572513TT6860R
Braeside, Melbourne, Victoria, Australia
Hire
Movers & Shakers
Jeannette Walker Jeannette Walker
CEO, MHEDA
President, European Rental Association (ERA)
Chief marketing officer, JLT Mobile Computers
Chief executive officer, East Penn Manufacturing
Crown RD572513TT6860R
Braeside, Melbourne, Victoria, Australia
Hire
Taylor TT300
Morgantown, Pennsylvania, United States
Used - Sale & Hire
USD98,500

PREMIUM business

F. Uchiyama
Global exporter of used forklift and construction machinery, servicing over 80 countries.
Fact of the week
The use of "hello" as a telephone greeting is attributed to Thomas Edison. He is said to have suggested it as a simpler alternative to other greetings, such as "Do I get you?" or "Are you there?".
Hangcha FLDCXT160
Braeside, Melbourne, Victoria, Australia
Hire
Terberg RT223
Balling, Denmark
Used - Sale
Upcoming industry events …
October 6-9, 2025 - Detroit, MI, United States
October 6-9, 2025 - Detroit, MI, United States
November 14, 2025 - Melbourne, Australia
Latest job alerts …
East Syracuse, United States
Saratoga, United States
Columbia, SC, United States
Indianapolis, IN, United States