Showing items 103,481 - 103,500 of 111,546 results.
Design & Engineering
Posted:
3 Dec 2008 23:45
by
johnr_j
genc c
This machine you have is a 1959 model year. I would suspect parts are really hard to find...
News & Perspectives
Posted:
3 Dec 2008 12:42
by
troy_m
R&R forklift parts in Kitchener, Ont is by far one of the best parts companies I've ever dealt with. I'd...
Design & Engineering
Posted:
3 Dec 2008 12:36
by
troy_m
does anybody have a source for a used or reman'd control board for a Genie TMZ34/19 tow behind unit ??
I...
Design & Engineering
Posted:
3 Dec 2008 12:33
by
troy_m
It sounds like you have a German built Clark 3 wheel forklift. The Model should be TM15S and serial #TM145...
Technical Troubleshooting
Posted:
3 Dec 2008 11:51
by
rob_w
M# J40zt S# J160n02587d
Controller, ZAPI Dualac2&HP
One error code shows up on rare occasions. # 12 Low voltage to steer...
Design & Engineering
Posted:
3 Dec 2008 11:36
by
rob_w
I have seen many Intake/Exhaust Manifold hardware loosen off over time causing vac. leaks. In turn this will cause some...
Storage & Handling
Posted:
3 Dec 2008 05:12
by
johnr_j
SMB1,
Food For Tought,
An accepted concept in one part of the world may not be readily accepted in another...
Design & Engineering
Posted:
3 Dec 2008 03:07
by
ben_g
only the reverse contactor does not engage.
Design & Engineering
Posted:
3 Dec 2008 03:06
by
elektrodrive
Also inspect the contactors associated with regen or Field weakening(if available) If the plug pins check out OK. It may...
Design & Engineering
Posted:
3 Dec 2008 01:41
by
justinm
for future info
that code 71 is for the REGEN current sensor by the 7rec not the main current sensor...
Design & Engineering
Posted:
3 Dec 2008 01:25
by
justinm
code 23 - fwd or rev coil current low when it should be high
is it showing code 23 in one...
Design & Engineering
Posted:
3 Dec 2008 01:25
by
bill_g
NEED TRANS OR PARTS FOR CATERPILLAR V300B
TRANS # 6Y5223
Design & Engineering
Posted:
3 Dec 2008 00:31
by
ben_g
well I change the setting truck worked good for 3 days now it showing code -23 I already check contactor...
Technical Troubleshooting
Posted:
2 Dec 2008 23:26
by
Prentice
Hello Cesar, I would say its your propane system. Check your coolant levels (when cold) If good you will have...
Design & Engineering
Posted:
2 Dec 2008 09:07
by
NoBody
Thank you all for your answers, but alas... The customer shipped it off to another division... (it ain't there problem...
Technical Troubleshooting
Posted:
2 Dec 2008 06:08
by
kevin_k
tim ,you can rebuild from the other end. the clutch packs are serviced from the bellhousing end. remove bellhousing ,then...
Technical Troubleshooting
Posted:
2 Dec 2008 05:23
by
Sparks
Hi,
Have you taken the Halfshafts out of the wheel hubs,
as these go into the diffential assembly?
Technical Troubleshooting
Posted:
2 Dec 2008 04:23
by
TimM
Hi all. I have a trans I am pulling to rebuild and it seams stuck in the diff. It will...
Technical Troubleshooting
Posted:
2 Dec 2008 04:23
by
Cesar333
Recently this customer presented me with his problem. When starting his Yale LP, it will start up fine and idle...
Safety & Training
Posted:
2 Dec 2008 04:03
by
gazb
Hello Jonathan_h
Thought I was not going mad, I have now stopped doing buisness with Training Provider
Did last course...
Forkliftaction.com accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.