I am restoring a STILL R70 forklift (1988). It has serious electric problems both the control circuit boards are suspect. Does anyone have the details on the boards?
Please help me out.
Thanks
Jerry
Showing items 21 - 36 of 36 results.
Hi All, I have a STILL R70 diesel / electric hybrid with a 2.5T lift capacity. I am after the wiring diagrams if any body has them for the following reason......I suspected that the engine was on the way out and have been using easy start to fire up in the mornings......however, since discovered that I am not getting the glow plugs hot enough....as we appear not to be getting the full 24 volts and around the circuit.......put new plugs in, replaced some of the wing and suspect either the batteries not man enough (does anybody know what they should be in Amp / hour?)......
Hello out there,I am glad I found you guys,Just been ripped off by local so called specialist,I have got an 1988 Still R70 TFG16,same old thing,engine starts,arms move up and down but no drive,replaced a few bits but could do with workshop manual or wiring diagram better than that let me have your number and I will ring you,or if your not far away I will pay for travel and some bear money,thanks for your time.
hi laci done that regards dave.
hello, write you your email adress in ABOUT or SIGNATURE.
Best regards, Laci
hi alan my truck is a r70 diesel 1988 it has a fault it will not go into drive or reverse it has been stood for two years started it up everything works engine is a vw 1600 forks work all lights on the truck work just wont go into drive any ideas ,have you got the manuals for this truck if so can you send them to me regards dave. or does any body have any ideas regards dave
Hi Alan My truck is STILL R70-16 sn: 70314605
Please could you let me know the serial number of the truck. I could possibly supply the drawing.
Or if you could pay the rent i will come and have a look
I have found a manual the has 28 pages that talk only about the test points and functions on the u200 and e36 boards.
The individual pins on the connectors are discussed one by one in the trouble shooting section.
The earlier service manauls did not have this info, but the later manual written for a later truck, has to be used with a pinch of salt. Essentially the design has stayed the same but there were efforts to improve from one generation of truck to another
I have a STILL R70 16(1995), I had lost the manual long ago, now my truck got a problem of the driving, it can able to start and raise the arm, but did not move, I supposed some component has damaged, I would like to have a electric drawing or service manual, every body would you help?
sorry i didnt post my e mail,its [email address removed],also note that any cost or fees involved will be reinbursed. advise
jerry p, this is larry perkins from louisville ky 15027276903.
would it be possible that you send me any information available on the still 4klb 1989 with diesel mercedes power?
note that the diesel cars are my speciality and i do a complete rebuild on the 4-5-6 clyl diesel,i fi can help just ask.
Hi gert,
I used the wiring diagram from the service manual. Eventually i replaced all elco's from the control circuit board and one cracked resistor. To my surprise the circuit board worked then i found out that the power board was damaged also. All the power transistors were removed and compared. One proofed to be damaged, this one was replace by a equivalent transistor bought at Conrad electronics. This solved the problem.
Send your email address and i will forward the drawings and pictures. By the way if you look carefully at your circuit board you may find components that have changed colour. These parts have been hot for a longer period of time, replace them and you may get lucky. I may take you several hours in the sun before you spot these parts.
Regards,
Gerrit
hi jerry,
do you have found any drawings?
i have the same problem with a diesel truck
Hi gary. The nameplate says TFG 2.5/7019, the service manual says R70-25T. It runs on LPG. You are correct it has a logic and a power board. I have the drawing on the electric wiring from the yellow service manual.
I am looking for the diagrams of the logic and power board and if possible an explanation on the purpose of measuring points on the boards.
Thanks
Hi...I have a bit of experience on these trucks. I take it that it has just 2 PCB,s...a power board & a logic board, also you don,t say if it diesel or gas & what size is IT?
By the way, I do not understand why the manufacturer doesn't release his nearly 20 years old design.
STILL GmbH, come one, put your 20-year-old stuff on the Internet!!
Forkliftaction accepts no responsibility for forum content and requires forum participants to adhere to our rules of conduct. Click here for more information.
If you are having trouble using the Discussion Forums, please contact us for help.