Hyster H3.0FT:
Hydraulic interlock Return to neutral

Hello,
This time i'm working on a another forklift Hyster 3.0 FT ( L177B33159J)

The DSC displayed the following message " Hydraulic interlock return to neutral".
With the DSC i have check the seat sensor. He is over 1.5 volt ( actually, 3.40 volt) so he is good.
Then i check the mini lever, always with the DSC. ( I also change it to be sure..) He is good too.
Any fault codes appears.

Could someone give me more information?

Best regards
Paul.
  • Posted 30 Jul 2014 06:57
  • Discussion started by PaulfromTahiti
  • Tahiti, French Polynesia
Showing items 1 - 8 of 8 results.
Hello BREWSKI,
pls can you send me calibration procedure manual also? i sure need it, i have the same problem ( hyd. interlock return to neutral)
Thanks vm.
  • Posted 29 Oct 2020 07:28
  • Reply by VZVTECH
  • Slovakia
Sounds like it needs the CDF flashed. This requires a laptop with the proper software and access to the CDF file. The CDF is only available to authorized dealers.
  • Posted 17 Aug 2016 22:33
  • Reply by BREWSKI
  • Nebraska, United States
I Have Another Machine, I Remove mini-lever and Replace it with Breakdown machine, Display show ( 30 second to shutdown) after 30 second nothing show on display.
I return back old mini lever, machine now showing only on display 30 sec. to shutdown & after 30 sec. nothing show even not crank the engine.
  • Posted 17 Aug 2016 17:25
  • Reply by KASBATIOUN
  • lagos, Nigeria
If it shows calibration out of range you need to replace the minilever.
  • Posted 16 Aug 2016 22:49
  • Reply by BREWSKI
  • Nebraska, United States
Hello, I have Same Problem, I'm Trying To Calibrate but always Showing on Display Calibration out of range
please can you help
  • Posted 16 Aug 2016 17:54
  • Reply by KASBATIOUN
  • lagos, Nigeria
Hello,
You have to calibrate the mini lever with the display.
Use the key "*" to select "enter password" in the menu with the arrows keys. The password is 55555. Then, go in the "calibrations" section and start the procedure you want to calibrate.
  • Posted 22 Oct 2014 06:08
  • Reply by PaulfromTahiti
  • Tahiti, French Polynesia
I am having the same issues and I dont know the procedure to calibrate them, any help is appritiated
  • Posted 17 Oct 2014 01:25
  • Reply by PacificAqua
  • Washington, United States
Problem solved!!
It came from the mini levers. One of them was Out of range and the neutral position was not detected. After the calibration procedures, the message disappear.
  • Posted 30 Jul 2014 08:04
  • Reply by PaulfromTahiti
  • Tahiti, French Polynesia

Having trouble using the Discussion Forums? Contact us for help.

Forkliftaction.com accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.

Inside Forkliftaction

Lately, we have commented on two noticeable phenomena - the rise of warehouse automation and the number of new forklift models being pumped into the market.
This week's newsletter reflects both of these themes which seem to have characterised our reporting for the year.
So, while other sectors appear to be
...Continue Reading

Next Editorial Features

1. ENERGY SOLUTIONS – March 2021
2. AUTOMATION AND ROBOTICS – May 2021

Inside Forkliftaction

Lately, we have commented on two noticeable phenomena - the rise of warehouse automation and the number of new forklift models being pumped into the market.
This week's newsletter reflects both of these themes which seem to have characterised our reporting for the year.
So, while other sectors appear to be
...Continue Reading

Inside Forkliftaction

Lately, we have commented on two noticeable phenomena - the rise of warehouse automation and the number of new forklift models being pumped into the market.
This week's newsletter reflects both of these themes which seem to have characterised our reporting for the year.
So, while other sectors appear to be
...Continue Reading

Next Editorial Features

1. ENERGY SOLUTIONS – March 2021
2. AUTOMATION AND ROBOTICS – May 2021