Storing your login information automatically.

When you select the 'Remember me' option, your login information will be stored on your computer in the form of a cookie. When you visit again, the stored login information will be retrieved automatically and you will not have to submit your login parameters (email address and password) each time you want to visit our members-only pages.

A cookie is a small piece of data that is sent to your browser from a web server and stored on your computer's hard drive. A cookie can't read data off your hard disk or read cookie files created by other sites. Cookies do not damage your system.

Marketplace NEW! Business Directory Discussion Forums Industry News Events Calendar Jobs & Resumes Photo Galleries
Business Directory
Discussion Forums
My profile
Industry News
Events Calendar
Jobs & Resumes
Photo Galleries


News service and business centre for materials handlingHOME
DISCUSSION FORUMS : Forkliftaction.communicate
Forum: Technical arena
Discussion:  Mitsubishi ignition wiring diagram
Number of messages: 12

Zachodniopomorskie, Poland

Hi, guys.
Looking for ignition wiring diagram or information how to connect ignition distributor to coil (with resistor) on Mitsubishi FG-15 with 4G33 engine. Know, that FG-25 with 4G52 engine has the same ignition system. Have a truck, where some "specialist" disconnect all wiring from ignition. Now, we trying to connect it back to previous state, but am worry to burn module, in case of fault.
Ignition distributor has two cable, coil has positive and negative, plus there is some resistor fixed to coil. Have one positive wire coming from main harness. Any help will be  much appreciated.

Posted 23 Nov 2010 04:33 AM Reply  Report this message
REPLIES: Sort replies by
Zuid-Holland, Netherlands
hi i have send the wiring in your mail..

regards  gc_d

Posted 23 Nov 2010 04:59 AM Reply  Report this message
Zachodniopomorskie, Poland

Thanks Geurt, but your diagram doesn't shows connection to resistor. Its probably older version with ignition points. If someone have diagram for version with ignitor(electronic module inside distributor) and can share it, i'll be more than happy! My email is in my signature.

Posted 23 Nov 2010 07:29 AM Reply  Report this message
New South Wales, Australia
Hi, Can you email me your circuit, having a lot of difficulties with burning out ignition module. [url/email removed]

Posted 1 Dec 2010 02:23 PM Reply  Report this message
Indiana, United States
We are also having a problem with the module burning out. Have a new OEM coil and resistor as well as a new module. But mechanic disconnected everything now we need the wiring diagram for this distributor and coil area. Help would be appreciated. Ours is model FG15 with four cylinder LPG. Thank you.

Posted 22 May 2012 04:38 AM Reply  Report this message
Zuid-Holland, Netherlands
Mail adress ?

Posted 23 May 2012 04:49 AM Reply  Report this message
Indiana, United States
[url/email removed]

Posted 23 May 2012 08:56 AM Reply  Report this message
Indiana, United States
they won;t allow an email address in this forum.  try this

info AT trialspartsusa DOT com

Posted 23 May 2012 08:57 AM Reply  Report this message
Indiana, United States
You might want to check for doides inside the wire harness on this truck. The resistor is used on the run side of the ign switch only. Good luck.

Posted 31 May 2012 10:06 AM Reply  Report this message
Victoria, Australia
I,m having same issue with a forklift.are you able to send me the wiring diagram for this set up???snake0427 @   Thank you in advance

Posted 13 Nov 2014 09:43 PM Reply  Report this message
North Carolina, United States

basic diagram i see with the resistor shows negative going to distributor
positive side has wire with resistor inline from ign side of keyswitch, and a 2nd wire leading to LP fuel solenoid, if gasoline then goes to fuel solenoid at carb.

You've been swooped!

Modified 14 Nov 2014 00:50 AM
by poster.
Reply  Report this message
California, United States
need wiring diagram for coil fg15 thank you

Posted 21 Jan 2016 10:08 AM Reply  Report this message accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.

Click for description.


Forkliftaction Media Pty Ltd
PO Box 1439
Milton QLD 4064