Hello. Where would I find a wiring diagram for a Crown 20mt?
Thankyou.
Showing items 21 - 40 of 63 results.
Thanks to the generosity of one of the forum members my 20mt130 is now equipped with one 12v desulfator unit per battery bank and a 50amp anderson plug connection for solar charging (in addition to retention of the on-board mains powered charger). The unit charges via connection to a 200w monocrystalline solar panel and 20 amp solar regulator with the desulfators maintaining all 4 batteries in excellent condition. Fitting of the anderson plug solar charging connection was fast and required only 2 connections to the unit.
Hi guys, sorry if this is a bit cheeky for my first post, but I have a 20mt130 walkie stacker which is used infrequently and is situated in a warehouse in a rural area (i.e. no mains power available to charge the truck batteries). I intend on installing a 12volt 200w solar panel which will run 2 x 12v charging circuits in parallel to keep the batteries charged (each 12v battery bank will also be fitted with a desulfator to preserve battery life). To do this I need a wiring diagram for my walkie, which I have been unable to find. If anyone is able to assist it would be greatly appreciated, my email address is swrfmaker at yahoo dot com dot au. I am happy to share the result through the forum once I get my solar charger completed as this is an area of increasing interest with rising energy costs.
HELLO EVERY ONE, I needpart catalog for crown model 20 M the serial number is 2A100613
Hi Crownie, Noticed you have a fair bit of knowledge in the forklift section, hoping you may be able to possibly help me with a crown 35RR (35RRTT198) model wiring diagram please?
Thanks in advanced mate.
John. Brisbane.
Do you have lift i.e. forks going up?
Mechatronic1,
Seeing as how the last response from someone to this thread was in January you are better off starting a new discussion to get a more timely response.
New to this site. Hope you found your manual. Have a Issue with a 20mt without slow or fast speed. Belly switch does engage a contactor but unit will not reverse direction it simply stops moving. Suspect resister. Anyone have any suggestions.
Do you have an owners manual for an MT20; serial# 35864
Email: [email address removed]
Jim Himes
Hi,Folks.Does anyone there might be have service manual to share it, for the Crown we / ws 2300 series.I do not know
the serial number.The error code is 27 -missing contactor,If anybody know the solution for this problem please send a message on tabak_08 at hotmail dot com.
Thanks in advance.
Is the motor turning when commanded to or no? if the motor is turning but wont go fwd or rev,then more than likely the key that holds the drive gear is sheared,have seen this on more than one occasion on them.
i am looking for a battery wiring diagram for a crown 20 mt 110 could someone email them to me. Bought truck with no batteries but have wires
Original post deleted...
Forkliftaction does not condone the selling or trading of propriety information including authorization codes or any other dealing of copyrighted material by unauthorised persons. Any correspondence about illegal activities on our forums could put you in breach. Forkliftaction would be obligated to pass your contact details to police authorities if they were requested.
Please do not post these types of material on our forums again.
Anyone have any experience troubleshooting the drive-wheel circuit on the 20MTs? The motor by the wheel is getting power from the 4 wires coming in, but when I twist the throttle it doesn't work in either direction, turtle or rabbit. I kind of suspect a fault somewhere in the switch circuit. But would appreciate the benefit of anyone's expertise.
Thanks!
Max
I also have a crown 20mt Forklift unit, and my service technician has pulled the batteries and has questions on the wiring of the batteries. If anybody can fax me a wiring schematic of this unit, that would be most helpful. My fax number is 215-695-3320.
If anyone has an old copy of the manual for this Crown it would be much appreciated. Since I last posted the motor works intermittently and it's leaking oil. :( Anyone can email me: jesse at deh-inc.com , Please HELP.!
Turning the key off and having the motor keep running proves that the solenoid is bad.
The button is on the handle. Sometimes it works and sometimes you get the clicking of the solenoid. Also when I was testing the motor would stay on even if I turned the key off and would have to disconnect the quick connect in order for it to stop. So test the solenoid on the motor?
Check on the batteries. Same as when we start our cars. Key on and start, can hear click/tuck but starter motor not running. Also check on the lift solenoid - you can jump the 2 big cables together to see whether the motor works. If this works, then change the solenoid. If the above do not work, then the possibility will be the lift motor.
brushes in pump motor? does it work only when you pull the lever on the valve or does the pump run with a button on the handle
The up function does not work all the tiume. It does once in a while but when it doesn't I hear the contacts clicking but motor does not go on. Loose wire, motor windings? who knows. Any advice or schematic would help. Thank you.
Forkliftaction accepts no responsibility for forum content and requires forum participants to adhere to our rules of conduct. Click here for more information.
If you are having trouble using the Discussion Forums, please contact us for help.