Storing your login information automatically.

When you select the 'Remember me' option, your login information will be stored on your computer in the form of a cookie. When you visit Forkliftaction.com again, the stored login information will be retrieved automatically and you will not have to submit your login parameters (email address and password) each time you want to visit our members-only pages.

A cookie is a small piece of data that is sent to your browser from a web server and stored on your computer's hard drive. A cookie can't read data off your hard disk or read cookie files created by other sites. Cookies do not damage your system.

Marketplace Business Directory Discussion Forums Spec-Checker Industry News Events Calendar Jobs & Resumes Photo Galleries
Marketplace
Business Directory
Discussion Forums
Home
My profile
Search
Spec-Checker
Industry News
Events Calendar
Jobs & Resumes
Photo Galleries


Ads








Ads
News service and business centre for materials handlingHOME
Search  
DISCUSSION FORUMS : Forkliftaction.communicate
Forum: Mechanical Troubleshooting
Brand: Tailift - Model: FG25
Number of messages: 7

START MESSAGE:
greenbastard
Saskatchewan, Canada
Ive been working on a tailift with a nissan engine. it runs fine, but when you use any working hydraulics it kills the engine. ive done an electrical tune up ie. plugs, cap rotor etc. and also bumped up the idle speed but it will stall when using hydraulics


Posted 14 Oct 2005 05:39 AM Reply  Report this message
REPLIES: Sort replies by
duodeluxe
New Hampshire, United States

We have experienced the same problem on a Toyota. We corrected it by installing an "idle up" device which is standard equipment on some TCM's with Nisaan engines. When the engine is "taxed" when using hydraulics or steering, it automatically increses the engine rpm's.

-------------------------
gitrucks@adelphia.net

Posted 14 Oct 2005 10:12 PM Reply  Report this message
greenbastard
Saskatchewan, Canada
i'll check it out, thanks

Posted 15 Oct 2005 04:18 AM Reply  Report this message
goncalosousa
Leiria, Portugal
I had the same problems same time behind, and is was solved simply through the adjustment of LPG Regulator.

Posted 7 Jan 2006 01:10 AM Reply  Report this message
HOTROD
Colorado, United States

On most nissan motors running gas or LP they have a dash pot that is a vacuum actuated solinoid, that is located on the side of the carb or mixer right above the throttle shaft. When the motor is under a load the vacuum drops and the dash pot will extend and  should increase the idle rpm to 1300-1800.  If the Tia lift does not have one you should make sure idle is at about 7-750, If it is pnuematic make sure the tire pressure is at max pressure for steering.  Make sure the Timing and fuel mixture are set right for your altitude.  If it is Electronic fuel injected you will need to go in with a scanner and check the paramaters for the fuel system

-------------------------
RODNEY BAKER
BLUE MOON LIFT SERVICE


Posted 13 Nov 2008 04:40 AM Reply  Report this message
meliftman
Alabama, United States

wouldn't hurt to check the hydraulic pressure, I have seen these problems occur when the hydraulic pressure is greater than it should be.

-------------------------
Liftman
Equipment, Inc.
Mobile, Al.


Posted 18 Oct 2013 07:03 AM Reply  Report this message
edward_t
South Carolina, United States

1st do what 'meliftman' suggests, then check/replace the return line filter and make sure the oil is the proper oil.
when you say, "use any working hydraulics" do you mean work the hydraulics at all (lifting an empty pallet 2 feet), or until they stall/load up the motor?
check the timing?

-------------------------
"it's not rocket surgery"


Posted 18 Oct 2013 10:11 AM Reply  Report this message

Ads

Forkliftaction.com accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.
Ads


GLOSSARY
Click for description.

FORUM
DISCUSSION
MESSAGES
NICKNAME
SIGNATURE

FORUMS
©Forkliftaction.com
Forkliftaction Media Pty Ltd
PO Box 1439
Milton QLD 4064
Australia