Storing your login information automatically.

When you select the 'Remember me' option, your login information will be stored on your computer in the form of a cookie. When you visit Forkliftaction.com again, the stored login information will be retrieved automatically and you will not have to submit your login parameters (email address and password) each time you want to visit our members-only pages.

A cookie is a small piece of data that is sent to your browser from a web server and stored on your computer's hard drive. A cookie can't read data off your hard disk or read cookie files created by other sites. Cookies do not damage your system.

Marketplace Business Directory Discussion Forums Spec-Checker Industry News Events Calendar Jobs & Resumes Photo Galleries
Marketplace
Business Directory
Discussion Forums
Home
My profile
Search
Spec-Checker
Industry News
Events Calendar
Jobs & Resumes
Photo Galleries




News service and business centre for materials handlingHOME
Search  
DISCUSSION FORUMS : Forkliftaction.communicate
Forum: Technical arena
Discussion:  Jugheinrich EFG320 error
Number of messages: 5

START MESSAGE:
ka_v
Victoria, Australia
Hi,

Getting the error code 084 on my jugheinrich efg320. This is the 2005 model.  

Drive function works, but as soon as i try to lift, tilt or side shift the error shows up.

Could you please help .

Thanks

Modified 11 Jun 2012 12:35 AM
by poster.
Reply  Report this message
REPLIES: Sort replies by
Karait
Poland

The code indicates the speed sensor fault (or the wires around), but you should have the traction problem too.
Anyway - check there.

-------------------------
I know your deepest secret fear...
J.M.


Posted 11 Jun 2012 10:49 PM Reply  Report this message
LACI
Serbia
Hello. For Error 084---
Faulty speed sensor:
 AS4803L:
- Speed changes by 50% within 4ms;
- Reference speed less than half the rated speed;
- Steer transmission blocked;
- Tear identification: a valid sensor reading is reduced to
zerowithin 4ms and remains at this level for 50ms without
producing a new valid reading.
 PM2402L/2 from V1.60:
- Too many pulses on encoder 3 on steer motor
Email adress???
Best regards, Laci

Posted 12 Jun 2012 03:07 AM Reply  Report this message
ka_v
Victoria, Australia
Hi,

Email address is [url/email removed]

The forklift will drive around without any faults, until i try to use the hydralics such as the lift tilt or side movement.  Can hear the motor starting and then in a few seconds the fault comes on and the motor stops.     The forklift itself can still drive forward, reverse and steer but the error 084 comes up and the lift tilt and side movement is disabled.

This only happened after doing a full recharge on the forklift. Not sure if it could be overcharged and this could create this problem. I have checked the hydralic fluid and it seems to be ok.

Thanks Hvala.



Posted 12 Jun 2012 04:49 PM Reply  Report this message
LACI
Serbia
Hello,
The control and probably 3 x MP1514 controller is solved. One of the hydraulics. Each module has a red and a green LED. The faulty module will flash the red LED. You must first calculate how many strobes. I exchange a defective module with one drive and migrates to the error when the module is bad, repair or replacement. Send me a drawing. Write me an email that there is enter your email address or yours is ABOUT.
Best regards, Laci

Posted 13 Jun 2012 01:58 AM Reply  Report this message


Forkliftaction.com accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.
FORUM GLOSSARY
Click for description.

FORUM
DISCUSSION
MESSAGES
NICKNAME
SIGNATURE

FORUMS
©Forkliftaction.com
Forkliftaction Media Pty Ltd
PO Box 1439
Milton QLD 4064
Australia