Forkliftaction.com

DISCUSSION FORUMS : Forkliftaction.communicate

My forum profile

Printable version

Discussion Forums Home

Forum:

Technical arena

Discussion:

Linde code's 221 280

Number of messages: 11

START MESSAGE:

julio_r
Texas, United States

julio_r
Texas, United States Hello, Everyone My name is Julio and we have 2 Linde's here in our plant, and we been running into problems the linde H50D is giving us some code "221" and "280" and just wondering if anybody can help me out here, once the code go off the linde wont lift anything and it runs in low speed like were forcing it, can someone please help me out I'm kind off new to linde's, I would be thankfull...

Posted 18 Aug 2009 02:08 AM

Report this message

REPLIES:

Sort replies by

Herald
lancashire, United Kingdom

Hi julio
The fault code 221 should have a T (traction) or L(hydraulics)before the code if it has a T then you have a voltage problem inside the controller.This fault will cut drive to creep speed.
The second code 280 is a hydraulic code and again is a low volage fault inside the controller.This fault will disable the hydraulics.
It looks like you will need to replace the control module in the cover behind the seat.
cheers
herald.

Posted 18 Aug 2009 07:47 AM

Report this message

julio_r
Texas, United States

Hi Herald I appreciate your help, this morning as we started the Linde it looks like the codes were gone but as I start to drive it around the forge shop I notice two different codes "T483" "T248" and now and very confused it looks like were going to have to get a Linde guy over to hook up the computer but this days there so expensive per hour......Thanks for you help Herald

Posted 19 Aug 2009 02:13 AM

Report this message

chublil
California, United States

If its a D series you will have to load the new controller too. Pathfinder is the software program and if your local dealer wont sell or share the software with you, take your issue to your regional Linde factory. You will absoulutly need this software for these units. Good Luck.

-------------------------
Fix it right!!!

Posted 19 Aug 2009 05:10 AM

Report this message

sergiopateiro
amora, Portugal

Hi, after you replace the module you need the program to calibrate evrything and to set the right machine, to do that you need pathfinder program and their hardware.

Posted 19 Aug 2009 06:40 AM

Report this message

chublil
California, United States

Yes you do. Pathfinder gives a list of model numbers, (350--351--352 etc. ) that all have different operating parameter. By downloading the appropriate version you are programming the unit with the model specifice parameters. You can use any dieseil or LP version to make the units work

Yes you do. Every controller is programmable for any model variation. Pathfinder loads the controller with the model specific info along with the input and output parameters based on the specifics of that model.

-------------------------
Fix it right!!!

Posted 19 Aug 2009 08:08 AM

Report this message

Herald
lancashire, United Kingdom

Pathfinder is for the newer 39 type trucks and late 350,
The 351+352 do not need any laptop work.The diesel+lp modules are not interchangeable they are specific to which fuel they use.The diesel module has engine settings that can be read with laptop.The gas truck also has a impco module fitted which again can be adjusted and interegated by the laptop using impco software.
The engineer with laptop will have to set up the the parameters to suit the customer requirements.
Hope this clears it up a bit
cheers
herald.

Posted 20 Aug 2009 05:52 AM

Report this message

tabak
nas. Karpos, Macedonia, The Former Yugoslav Republic of

hi,folks.
Can someone help me.I have program for diagnostics,but i need cable.
Where I can get,for linde R114 or R115.
thanks.

Posted 29 Aug 2009 06:30 AM

Report this message

michel_v
noord holland, Netherlands

order de cables by linde

Posted 3 Sep 2009 02:26 AM

Report this message

marko
Croatia

Hello Tabak

Please mal me at

var at zg.t-com.hr

hvala

Posted 7 Oct 2009 06:41 AM

Report this message

Billy_B
Slovenia, Slovenia

Tabak:

If you need cables please send me an e-mail. I have my e-mail in my profile if you click my nickname.
Have software too!

Posted 8 Oct 2009 07:44 AM

Report this message

Forkliftaction.com accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.

FORUM GLOSSARY

Click for description.

FORUM

DISCUSSION

MESSAGES

NICKNAME

SIGNATURE

FORUMS

Discuss: Industry News & Whispers

Discuss: Conferences, trade shows & other events

Discuss: Mechanical Troubleshooting

Discuss: Technical arena. Did you know? Who knows?

Discuss: Machines. Forklifts, stackers, telehandlers, container handlers and reach stackers

Discuss: Business issues

Discuss: Safety, training & legislation

Discuss: Fun at work